• Welcome to H4O! For a reduced ad experience, please login or register with the forum.

H3 led light bar mounts...

derian06

derian06

Red Rockett
Messages
1,866
Location
Madison, AL
And i broke the bolt that is used for the rivnuts by the way. The whole wrench thing didnt work for me


Sent from my iPhone using Tapatalk
 
derian06

derian06

Red Rockett
Messages
1,866
Location
Madison, AL
uru5azyr.jpg
muda2eda.jpg


Fits perfectly, i'm happy with it. But this thing is broken all over
yse7eqa3.jpg
asava3uv.jpg



Sent from my iPhone using Tapatalk
 
benlaud87

benlaud87

Well-Known Member
Messages
849
Location
Maryland
The rivnut tool makes things much easier. What side is broken? I have a passenger a pillar but it's drilled for marker lights.
 
poweraidon

poweraidon

Well-Known Member
Messages
830
Location
georgia
derian06 said:
e9y3ugeq.jpg


So i drilled a hole small enough to where only the nut would fit because i couldnt get the riv nut to work, whats the problem with doing it this way? It seems sturdy


Sent from my iPhone using Tapatalk
Click to expand...

The bolt doesn't just fall out?


Sent from my iPhone using Tapatalk
 
derian06

derian06

Red Rockett
Messages
1,866
Location
Madison, AL
poweraidon said:
The bolt doesn't just fall out?


Sent from my iPhone using Tapatalk
Click to expand...

Nope, did both sides. It could be tighter, but i think its going to leave just enough flex to fit the 52" light bar, if it is a 52. But the mounts definantly aren't going anywhere any time soon. I completely forgot the trim so I had to re drill some holes, but it all worked out alright. My bar should be here in a couple of hours. I already have everything wired I just have to put it in the holes and plug it in.


Sent from my iPhone using Tapatalk
 
poweraidon

poweraidon

Well-Known Member
Messages
830
Location
georgia
derian06 said:
Nope, did both sides. It could be tighter, but i think its going to leave just enough flex to fit the 52" light bar, if it is a 52. But the mounts definantly aren't going anywhere any time soon. I completely forgot the trim so I had to re drill some holes, but it all worked out alright. My bar should be here in a couple of hours. I already have everything wired I just have to put it in the holes and plug it in.


Sent from my iPhone using Tapatalk
Click to expand...

What size drill bit did you use?


Sent from my iPhone using Tapatalk
 
derian06

derian06

Red Rockett
Messages
1,866
Location
Madison, AL
flexed
qu5a9y5a.jpg


Normal
ysemaguv.jpg


New battery terminals and distribution block, it was less than 30$ and well worth it.
9ehyqa7u.jpg



Sent from my iPhone using Tapatalk
 
derian06

derian06

Red Rockett
Messages
1,866
Location
Madison, AL
poweraidon said:
What size drill bit did you use?


Sent from my iPhone using Tapatalk
Click to expand...

No idea, I just looked for one close to a similar size (they're scattered all around my garage), and took a chance. but i also used, same thickness nuts, but alot longer and the ridges were deeper.


Sent from my iPhone using Tapatalk
 
Ron46

Ron46

Capt.
Messages
807
Location
NJ
[video=youtube;rMcPWM-YkR0]http://www.youtube.com/watch?v=rMcPWM-YkR0[/video]

SolidusJ said:
I RATHER BE DEAD THEN RED!!!! RI has some china stuff in it but I haven't seen the cheap ones make a video like this.

[video=youtube;wuIU-Mg0EMM]https://www.youtube.com/watch?v=wuIU-Mg0EMM[/video]
Click to expand...
 
You must log in or register to reply here.
Top