• Welcome to H4O! For a reduced ad experience, please login or register with the forum.
  • The Swap Meet is not a regulated market, and buyers/sellers are not screened. Please do your homework before agreeing to anyone for any purchases or sales. If you have any questions about the user, please contact @Alrock via private message and I will attempt to provide any relevant information about the person, including location based on IP address. This is not a guarantee or promise of delivery but the addtional information may be helpful to you in your transaction. There are no guarantees here so use your judgement. Consider payment options like PayPal that have recourse (only when treated as a sale, and not as % between friends). Scammers will often use Zelle or ask for PayPal between friends because you cannot reclaim the money in the event of fraud or non-delivery. If a user has just joined and/or has few posts they should be viewed very cautiously.

Hunner EXtreme spring/shock skids

Hunner

Well-Known Member
Messages
2,334
Location
Arkansas
I hope to have 10 sets in about two weeks or more. Just a little slow this time. Post up if you need them, I don't! lol

Laser cut from 1/4 pickled steel 10/10. The brackets are indexed in a slot for alignment and strength and welded on top and bottom. Gussets on the taller one. Holes in brackets are elongated for wiggle room installing. Bottom holes are big enough for a heavy impact socket.
I media blast them so they are ready to paint.
New design change has the rear skid angle "start" back 1 1/2" to allow extra clearance for bigger shock mounting eyes (Bilstein) but I am running the old style with Bilsteins, no problem.
$165 for a pair of rear and front hanger skids. Including shipped flat rate, 3 day to most anywhere (as long as the Post Office stays in business)
Install thread
http://www.hummer4x4offroad.com/for...-SKIDS-Hunner-EXtreme-install&p=2973#post2973
C3483_resize.jpg

DAH_3706_resize.jpg

DAH_3555_resize.jpg

_DSC3582_resize.jpg

3579_resize.jpg

DAH_5594.jpg

4736.jpg

Without
_DSC2862_resize.jpg

bentspringplate.jpg
 
Last edited:

Hans3T

Lif"T"ed
Messages
3,035
Location
NC
I'll say that these are a really great product. They protect the shocks & skids unbelievably well. If you don't have set, and if you do any wheeling, get yourself a set ASAP!
 

PacNWAg98

Well-Known Member
Messages
56
Location
Issaquah, WA
Hi guys - Got my Hunner Xtreme skids on my rig today. They are fresh and just a few hours old.
With a high quality red paint job (pre-weld) :)

Thanks Dave (aka Hunner), for the great product - these babies are ready to get hammered! Let me know if you'd like photos from any other angles.

Capture 1.jpgCapture 2.jpgCapture 3.jpgCapture 4.jpg

DAVE
 

Hunner

Well-Known Member
Messages
2,334
Location
Arkansas
Great. Yeah let's see some when you break them in or with a huge rock you "skidded" over.:)
 

Bigunit

Hammer Down!
Staff member
Messages
6,561
Location
Arizona
They are a great product. I've purchased 2 sets from Hunner & have the front, rear spring carrier skids welded on my T. Everyone should have these on their rig!
 

kshummer

Member
Messages
19
Location
Kansas
Can I ask a dumb question, if I weld on the hanger skid, can you still remove the spring pack easily or do you need to grind off the skid before you can remove them?

Thanks!
 

Hunner

Well-Known Member
Messages
2,334
Location
Arkansas
No question is dumb, you are thinking ahead.
I am not sure of anyone actually removing the springs with them on. I thought at one time Brodie looked at doing that and posted he thought they would clear. Can't remember for sure. When I first did them I figured the arc needed to lift the springs up and out and think that was possible. Since that time I have made the front one angled back a little more after people wondering that. I was figuring dropping the rear end of the spring and then lifting out the front.
Anyway new ones should work. Maybe some day some one can tell us for sure.
I have cut a pair of thinner front ones off to put on the new style 1/4 inch using a thin grinder blade.

Many post ago I commented on thinking of a way to bolt those on. Unfortunately GM put in the bolt on the drivers side before the fuel tank. That would require removing the tank the first time. Then I would have to have made side plates of some sort adding to labor and weight. The only surface in contact is on the frame. I don't recommend drilling into the frame. Then you would have a problem with bolt heads sticking out or using recessed bolts in the 1/4 material not leaving much thickness in the area to attach them. A really hard drop on a rock shelf could knock them off was my thinking.
People that did not get good penetration on the weld have knocked them off. If you think anytime soon you are going to replace the spring pack just well them in the front where they contact the uneven fold in the frame and about three short welds down the out side you can get to and grind off if needed.
This is a shot where I had cut off the 3/16 skid and was fitting a 1/4.
DAH_3714_resize.jpg

DAH_8037-1.jpg

cr8046.jpg

It's a little harder to mount them when the front hanger looks like this
_DSC2862_resize.jpg
 
Last edited:

Hunner

Well-Known Member
Messages
2,334
Location
Arkansas
The rear ones are the big ones that go under the spring hanger u-bolts AND protect the shock. The smaller ones are for the front mount for the rear springs. If you just want those small front ones they are $50 shipped.
DAH_3714_resize.jpg
 
Last edited:
Top